Ghost Immobiliser Fitting
Protect your vehicle against key theft, cloning, and hacking using the first aftermarket CAN-Immobiliser. With the additional option to connect to an Ghost app and GPS tracking system that will notify you via phone in the event that your vehicle is damaged with or stolen.
The installation of a Ghost immobiliser is done by a trained technician. The right tools, insulation tape, and heat shrink tubing is crucial.
Getting Started
Unlike physical theft protection devices like wheel locks or car alarms, ghost immobilisers protect your vehicle without the need of LED indications or key fobs. They are directly connected to the ECU CAN data network and are activated only after entering a PIN. This provides a higher level of protection against key hacking, ECU swapping and cloning.
Therefore, the installation of a ghost immobiliser Birmingham is a task that must be carried out with great agility and precision. It's like navigating the minefield. A single mistake could cause severe damage to the circuits of your vehicle's electrical system. It is essential to comprehend the installation procedure and prepare your vehicle in a timely manner.
First, you need to prepare the vehicle by removing interior panels to allow for the immobiliser unit. Once ghost immobiliser cost have found the ideal place to hide it, use cable tie to fix it. Then, tidy your wiring by making sure that loose wires are tied down and using insulation tape to cover exposed connections. This reduces the chance of a short circuit that is not intended to happen and improve the appearance and reducing the risk of theft.
Finally, identify a source of continuous 12V power and a grounding location for the ghost immobiliser. Once you've located these, test the power wires using a multimeter to ensure they're delivering a consistent voltage. Connect the CAN H and CAN L wires of the immobiliser to the power source and grounding points.
It's important that you ensure that all connections are checked and check the immobiliser to look for indications of corrosion. Also, test the system to make sure it's functioning properly by entering a PIN code and then starting the engine. This should become a part of your daily routine since it allows you to identify any intermittent problems early. Regular testing will also help to prolong the life of the device and ensure it's functioning at its best.
Preparing the Vehicle
Installing a Ghost immobiliser requires knowledge and tools. A wiring diagram is crucial for finding the correct wires, establishing precise connections and ensuring safety. A multimeter can be used to verify electrical values and guarantee security. Insulation tape and cable ties can be used to shield the connections from tampering and to ensure they are secured. ghost immobiliser birmingham is available for your Ghost Immobiliser. It will give you specific instructions specifically tailored to the model.
Once installed the ghost immobiliser will stop unauthorised engine start-ups by requiring the driver to enter a unique code using the buttons on the steering wheel or console. The code can be altered at anytime by the vehicle owner, either manually or remotely via an app for mobile devices. The device is also quiet and is undetectable by thieves because it doesn't emit any radio frequencies.
Ghost immobilisers connect directly to the vehicle's CAN bus. It is a network that communicates with all the vehicle's electronic control units (ECUs). It intercepts signals generated by the ECUs and prevents the engine from starting if the ECU detects a false signal. The system is weatherproof and tamper-proof. It has no keys or LED indicators to attract thieves' attention.
It can be positioned behind the dashboard or in a hidden area, so it isn't visible to thieves and does not interfere with the vehicle's performance. It can be mounted in a small jar, so that it is less likely to be spotted by untrustworthy salespeople during a test drive.
Its stealthy operation, along with its integration into the CAN-bus system of the vehicle, is a powerful deterrent to modern car theft methods such as signal relay attacks and key cloning. The system can be integrated with other security measures to create an effective barrier that can thwart even the most obstinate thieves. This is why more and more insurance companies are now suggesting or even requiring ghost immobilisers be installed, as it will significantly lower monthly premiums.
Making Connections
Ghost immobilisers are silent, unlike traditional security systems which can be heard by thieves. They prevent thieves from knowing that your vehicle is in operation. ghost immobiliser birmingham prevent high-tech methods of theft, such as OBD hacking. Installing them without leaving permanent marks on your car is a great option for those who plan to sell the vehicle in the near future.
The Autowatch Ghost 2 CANbus immobiliser is among the newest and most reliable methods for preventing car theft. It blocks your engine through the CAN data network and generates a unique PIN code which is difficult to steal from criminals. It can be used in many different automobiles, and it can work with all the features that are already in place, such as car alarms, steering wheel locks, GPS trackers, and door lock bypass.
If you decide to go with an Ghost immobiliser, make sure to refer to the wiring diagram for your specific vehicle model to determine the wires to connect. Check their locations to make sure they are accurate, and label them or tape them to help remember them. You'll also need to locate a constant power source (12V) for the system, as well as the grounding. Once you have these in place, you are able to begin to connect the components to complete the installation.
The ghost immobiliser won't allow your vehicle to start until you enter a pin code through the buttons on the dashboard or steering wheel. This will stop ECU replication and other methods of theft of vehicles. It can also be paired with other Thatcham approved security devices such as alarms or tyre clips to provide your vehicle with an even greater degree of security.
As the UK automotive industry grows, and so do the options to secure your vehicle. With so many ways for thieves to gain access and take your car it's crucial to take every precaution to ensure it isn't stolen. This is why ghost immobilisers are very popular among responsible car owners.
Testing the System
The Ghost Immobiliser communicates with the vehicle's ECU via a CAN network. This stops the engine from starting until the PIN code has been entered. This makes it difficult for thieves to steal the key fob that you use to start your vehicle, and difficult to disable the system by hacking its electronics.
Ghost Immobilisers can also be used with GPS tracking devices to assist you to locate your vehicle in the event that it's stolen. This isn't an everyday feature in security products sold by the aftermarket however it's an excellent option to increase your security and provide peace of mind knowing your vehicle is protected.
The Ghost-II immobiliser not only provides greater security, but also a convenient experience for the user, by not having to use additional key fobs or devices. It is simple and user-friendly PIN code entry system that works seamlessly with your everyday routine. It also comes with convenience features and deactivation options that allow you to temporarily disable the immobiliser to valet park or service your vehicle.
Prepare the necessary tools and familiarise yourself first with the wiring of your vehicle. A basic set of hand tools will give you the ability to make precise connections, while a multimeter will help check electrical values. Insulation tape and heat-shrink tubing is essential to safeguard connections from short circuits. Cable ties can be used to secure wiring. Lastly, it's important to work in a well-lit location and wear safety gear when working with tools and electrical components.
After you've completed the installation, you must test the Ghost immobiliser to ensure that it's working as intended. It is recommended to first start the vehicle without entering the PIN. If this doesn't work, you will need to test again and examine the connections more thoroughly.
In contrast to other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is much more effective than conventional physical deterrents, such as wheel clamps or steering locks. It is TASSA recognized and approved by some insurance companies, making it an investment that's cost-effective and can give you the peace of mind that you want.